This website uses cookies. By using this site, you consent to the use of cookies. For more information, please take a look at our Privacy Policy.
Home > FPGA Technical Tutorials > FPGA-Based Prototyping Methodology > Which platform? (2) ready-made > On-board support for signal multiplexing

TABLE OF CONTENTS

Xilinx FPGA FPGA Forum

On-board support for signal multiplexing

FONT SIZE : AAA

The concept of time division multiplexing (TDM) and its ability to increase effective IO between FPGAs is well understood and it is not difficult to see how two or more signals may share the same interconnect path between FPGA pins. The TDM approach would need mux and de-mux logic inside the FPGA and would need a way to keep the two ends synchronized. It is also necessary to run the TDM paths at a higher rate than the FPGA’s internal logic, and also ensure that signals arriving at the mux or leaving the de-mux both meet the necessary timing constraints. This would be a complex task to perform manually, so EDA tools have been developed that can insert TDM logic automatically, analyze timing and even choose which signals to populate the muxes with. The prime example of such an EDA tool is the Certify® tool from Synopsys, which supports a number of different asynchronous and asynchronous models for TDM. 

Whichever tool is used, the problem still exists that with muxing employed, either the overall FPGA-based prototype must run at a lower speed or the on-board paths must be able to run at a higher speed. TDM ratios of 8:1 or higher are not uncommon, in those cases, a design which runs at 16MHz inside the FPGAs must be either scaled back to 2MHz (which is hardly better than an emulator!) or the external signals must be propagated between the FPGAs at 128MHz or greater, or some compromise between these two extremes. With the need for high multiplexing ratios in some FPGA-based prototypes, the overall performance can be limited by the speed at which TDM paths can be run. A good differentiator between boards is therefore their ability to run external signals at high speed and with good reliability; a noisy board will possibly introduce glitches into the TDM stream and upset the synchronizations between its ends. 

Beyond simple TDM, it is becoming possible to use the LVDS (low voltage differential signaling) capability of modern FPGA pins in order to run on-board paths at speeds up to 1GHz. This full speed requires very good board-level propagation characteristics between the FPGAs. Figure 65 gives a non-detailed example of a serial TDM arrangement, which allows eight signals to be transferred across one pair of differential signals (further detail in chapter 8). 

At a high transmission speed of 800MHz and a multiplexing ratio of 8:1, the128MHz speed in our previous example could easily be supported, and even increased to a ratio of 40:1, as long as the board is good enough. The possibility to run much higher mux ratios gives a large increase in the usable connectivity between FPGAs. For example, a TDM ratio of 64:2 (2 rather than 1 because of the differential pins required) could be supported on prototypes running at 30MHz or 

Figure 65: High Speed TDM using differential signaling between FPGAs

High Speed TDM using differential signaling between FPGAs.png

more, making it much easier for the EDA tools to partition and map any given design. There is more on the discussion of TDM in chapter 8. 

So, once again, a good differentiator between FPGA boards is their ability to support good quality LVDS signaling for higher overall performance and to supply the necessary voltage and IO power to the FPGAs to support LVDS. It is also important that designers and indeed the tools they employ for partitioning understand which board traces will be matched in length and able to carry good quality differential signals. A good board will offer as many of such pairs as possible and will offer tool or utility support to allocate those pairs to the most appropriate signals. For example, the HAPS-60 series boards from Synopsys have been designed to maximize opportunity for LVDS-based TDM. Details of LVDS capability in each Virtex-6 device and signal routing on the HAPS-60 board is built into the Certify tools to provide an automated HSTDM (high-speed TDM) capability. This example again underlines the benefit of using boards and tools developed in harness. 

  • XC2C128-7CPG132C

    Manufacturer:Xilinx

  • CPLD CoolRunner -II Family 3K Gates 128 Macro Cells 152MHz 0.18um Technology 1.8V 132-Pin CSBGA
  • Product Categories: Embedded - CPLDs (Complex Programmable Logic Devices)

    Lifecycle:Active Active

    RoHS:

  • XC2C128-7TQG144C

    Manufacturer:Xilinx

  • CPLD CoolRunner -II Family 3K Gates 128 Macro Cells 152MHz 0.18um Technology 1.8V 144-Pin TQFP
  • Product Categories: CPLDs

    Lifecycle:Active Active

    RoHS:

  • XC3S400-4FG320I

    Manufacturer:Xilinx

  • FPGA Spartan-3 Family 400K Gates 8064 Cells 630MHz 90nm Technology 1.2V 320-Pin FBGA
  • Product Categories: FPGAs

    Lifecycle:Active Active

    RoHS:

  • XC5204-6PC84I

    Manufacturer:Xilinx

  • FPGA XC5200 Family 6K Gates 480 Cells 83MHz 0.5um Technology 5V 84-Pin PLCC
  • Product Categories:

    Lifecycle:Obsolete -

    RoHS: No RoHS

  • XC5204-6PQG160C

    Manufacturer:Xilinx

  • FPGA XC5200 Family 6K Gates 480 Cells 83MHz 0.5um Technology 5V 160-Pin PQFP
  • Product Categories:

    Lifecycle:Obsolete -

    RoHS:

Need Help?

Support

If you have any questions about the product and related issues, Please contact us.